It's The Complete List Of Subaru Car Keys Dos And Don'ts > 자유게시판

How to Programming a Subaru Key Fob at Home

Depending on how old your subaru key programmer is, you might need to have your key fob programmed by an automotive locksmith. This is typically accomplished by connecting a machine for programming to the computer in the vehicle.

To program your Subaru begin by opening the driver's doors using the door button control and then shut it. You will hear a chime on the instrument panel, and the dome lights will blink.

Step 1: Locate the Transmitter Circuit Board

There are a variety of ways to program your key fob. First, you must determine what kind of key fob you have. You can determine this by taking a look at the shape of the key fob or by listening to your car's sound.

Once you have the information and have it, you can begin the process of programming your keyfob from home. To accomplish this, you'll need a metal key and a screwdriver that has a flathead. The key fob can be opened by twisting. Then push the key in and release the battery from the small tabs that secure it. Replace the battery with a fresh one and then put the key fob case back together.

Step 2: Remove the key fob case

It is recommended to replace the batteries in key fobs in case they're not functioning. However, there are some situations where the buttons on the key fob could be broken. If you see that the contacts made of metal on the button are loose, try soldering them in place to allow them to work again.

Before you begin the process, ensure the doors of your car are shut and the ignition is off. Close the driver's door and press your button 10 times in rapid succession. Then, you should hear the instrument panel chime and your dome lights will flash. This means that you are in a position to proceed.

Step 3: Insert the fob of your key into the ignition

Many articles on the internet will show you how to program your new or replacement subaru key fob subaru key fob cost keyfob at home. However, many of them do not give very specific instructions. Reprogramming a key that is electronic is best done by an experienced auto dealer in Fort Bliss or a locksmith.

Sit in the driver's seat with the doors shut and the engine turned off. Use the door button to unlock all of the doors. Open and close the driver’s door three times. Then, insert and remove the key from the ignition switch (don't turn it) 10 times within 40 seconds. The system will vibrate when the settings are altered.

Step 4: Turn the Ignition On

It is crucial to understand that this method of programming a key fob works if you already have a working key. If not then a dealer or auto-locksmith will be required to program keys for your Subaru Fort Bliss.

After the key is programmed, it will be able to start your vehicle within five minutes. To begin, make sure all doors are shut and the engine is turned off. Assume a seat in the driver's chair and unlock all doors using the button on the door. Insert the key into the ignition and turn it off to the first position (the electrical systems will come on, but the engine is off) Then, turn it back to the off position ten times in rapid succession.

Step 5: Unlock Driver's Door

Subaru offers many high-end vehicles with key fobs that lock and unlock doors, start the engine, and even defrost windows. These gadgets can sometimes stop functioning.

Find a locksmith or dealer to fix the problem. This will fix the problem and make sure that your car is safe.

It is necessary to first open and close the driver's door. Then, put the ignition key in and turn it to the first position. Then, turn it back to the off position. Do this as fast as you can ten times. After tenth attempt you should hear a sound.

Step 6: Press the Lock/Unlock button on the driver's Door

The procedure for replacing a subaru key the battery in the Subaru remote key fob is very simple. Unlock the exterior fob case. Then, use an flathead screwdriver, to pry open the internal case and take out the old battery.

After removing the old battery, put in the new one and close the case. Then, sit in the driver's seated position and unlock all doors using the door button control. After that, put the key in the ignition and turn it so that the electrical systems are turned on but the engine is off. Repeat this 10 times in succession until you hear the chime coming from the instrument panel. This will bring the system into programming mode.

Step 7: Press on the Passenger Door Lock/Unlock button

For some owners, the annoyance noise that occurs when locking and unlocking the Subaru key fob from outside the vehicle could be distracting. In some instances the chirp may be turned off by closing and opening all doors, and then a double-click of the lock button on the key fob.

Switch off the ignition and close all doors, as well as the lid for the fuel-filler. Press and hold the lock side of the key fob's lock button for 10 seconds. The instrument panel emits a chime after this is done. The chime indicates that the fuel-filler lid and door lid are locked. The setting can be changed to make the doors and fuel-filler lid are locked automatically without pressing the request switch.

Step 8: Enter the 8-Digit Transmission Number

Write down the first series of 8-digits and keep it in a safe place. Now, get into the driver's seat, shut the doors and turn the ignition to the first position. After ten turns your instrument panel should sound once.

Then, you need to open the case for the key fob and locate the circuit board for the transmitter inside. The circuit board should have one or two 8-digit numbers. Take note of the sequence that starts with the first number, and follow the steps in this guide to register the code in the system of your vehicle. For older models, this procedure may require a visit the dealer.